Vartų pultelių video programavimo, pririšimo instrukcija
Garažo vartų pulteliai ir imtuvai, Universalus pultelis HR Multi suderinamas su visomis automatikomis, HR Pultelių programavimas nereikalauja įrankių ir įgūdžių
ADYX pultelio programavimas
APERTO pulteliu pririšimas
APRIMATIC pultų pririsimas
BENINCA pultelio pririšimas
BFT pulteliai programavimas
CAME pultelio pririšimas
CAME SPACE PL pririšimas
CHINA pultu programavimas
CLEMSA Mutancode manual
DITEC pririsimo instrukcija
ERREKA pulteliu pririšimas
FAAC pulteliu programavimas
GARRISON pulteliu kopijavimas
GENIUS pultelio pririšimas
GIBIDI pultelio programavimas
Hermetiško vartų pultelio programavimas
HORMANN programavimas
HR Matic programavimas
JEKO pultelis programavimas
KEY pulteliai programavimas
LIFTMASTER programavimas
MARANTEC pulto kopijavimas
MHOUSE pulteliu pririsimas
NICE pulteliu programavimas
NOVOFERM pultu pririsimas
PRASTEL pultelio pririšimas
PROGET pultelio programavimas
PROTECO pulteliu programavimas
RIB pulteliu programavimas
ROGER pultelio kopijavimas
SOMFY pultelio pririšimas
SOMMER pultelio pririšimas
TX PULT/ROLL pultelio kopijavimas
V2 pulteliai programavimas
VDS pultelio programavimas
WHY EVO/SimSim pultelio kopijavimas
PRASTEL pultelio pririšimas
 
Vartu garažo pulteliai  Prastel sistemoms, tinka universalus pultelis HR
Prekiaujame pulteliais, tinka visiems pulteliams Prastel t. sk. 433,92 dažnio, kopijuojame Prastel pultelius, ir kitų Prastel vartu pulteliu programavimas. 

• Galimybė įrašyti iki keturių skirtingų siųstuvų kodų
• Pultelio korpusas : plastikas.
• Kompaktiškas - patogu naudoti kaip raktų pakabuką. 

PRASTEL Remote synchronisation procedure.
1. Stand near the receiver with the synchronised device.
2. Press and release buttons 1 and 2 simultaneously.
3. The led on the remote control will light up after 2 seconds and turn off.
4.  When the led on the remote control lights up again, simultaneously press buttons 1 and 2 and hold until the led begins to flash.
5.  When the led stops flashing, press the button of the remote you desire to program. 6. The receiver will save the code.
Direct PRASTEL synchronisation procedure.
1. Open the receiver.
2.  Press the “ENTER RADIO” button. All the red leds will light up for 2 seconds, after which only the first led will remain lit.
3.  Press the “SET” button repeatedly to select the relay you wish to associate with the transmission.
4.  Press the desired button to transmit the code. Each button (channel) transmits a different code. a.  The led flashes slowly during synchronisation and remains steady once the operation has been successfully concluded. b. I f a led begins to flash quickly, it means that this channel has already been synchronised. c.  If all the leds flash at once it means that the memory is full. The code has not been stored.
5.  Repeat the operation for all buttons (channels) you wish to synchronise, always selecting the relay to which they are to be associated.
6. Repeat the operation for all the remote controls you wish to synchronise.
7.  Press “ENTER RADIO” again to exit synchronisation mode. The leds will turn off. The device will exit synchronisation mode automatically 10 seconds after the last operation. 8. The codes are stored and will not be deleted even in the event of a power cut.
Visi pulteliai vienameVartu pulteliai programavimasVartu pulteliu remontasVartu automatikos priedaiKontaktai Vilniuje, Kaune